anthonym Posted October 15, 2019 Share Posted October 15, 2019 Anyone know these and if there is an official doc?I need the comparison from standard to present settings for the non uk mot to get Nitrons approved.This was with standard Bilsteins fitted. anthony Link to comment Share on other sites More sharing options...
SM25T Posted October 15, 2019 Share Posted October 15, 2019 General guide ... with your weight in driver seat .... set front height so the sump is at least 65-75mm off the ground. Then set rear +15mm above front height. Measured under chassis rails .... front at rear of cycle wing and rear at front of wing. Link to comment Share on other sites More sharing options...
anthonym Posted October 15, 2019 Author Share Posted October 15, 2019 Not how to set it, I need the delivery settings for u.se as an official "before" set of numbers. Link to comment Share on other sites More sharing options...
revilla Posted October 15, 2019 Share Posted October 15, 2019 I don't there really are "official" settings. They just come as they come - probably all over the place! Link to comment Share on other sites More sharing options...
revilla Posted October 15, 2019 Share Posted October 15, 2019 The assembly guide is as close as you'll get and agrees with Ian: Link to comment Share on other sites More sharing options...
anthonym Posted October 15, 2019 Author Share Posted October 15, 2019 aye I suspected that may be the case. I'll explore further... Link to comment Share on other sites More sharing options...
SM25T Posted October 15, 2019 Share Posted October 15, 2019 I am 'official' !!! Link to comment Share on other sites More sharing options...
anthonym Posted October 15, 2019 Author Share Posted October 15, 2019 I wish :-) Link to comment Share on other sites More sharing options...
anthonym Posted October 15, 2019 Author Share Posted October 15, 2019 they seem to want ride heights as measured from the centre wheel cap to the bodywork.. so rear is ok and it gradually dawned on me the front could be from centre wheel hub to cycle wing. Seems daft to me, but I suppose what works is what works. Link to comment Share on other sites More sharing options...
revilla Posted October 15, 2019 Share Posted October 15, 2019 Front ride height from wheel centre to cycle wing will work until they want you to adjust it in the dampers. Link to comment Share on other sites More sharing options...
rj Posted October 15, 2019 Share Posted October 15, 2019 Front wishbones horisontal and 15-20mm rake should be close to optimal. Beware that the ZZS' are 185 at the front whereas the CR500s were 175. I had to adjust for this to reclaim handling. Link to comment Share on other sites More sharing options...
anthonym Posted October 15, 2019 Author Share Posted October 15, 2019 Adjust how? Can't say I relish when I will have to switch. Link to comment Share on other sites More sharing options...
7 wonders of the world Posted October 16, 2019 Share Posted October 16, 2019 How about redressing the Nitrons with some Billy decals...... Link to comment Share on other sites More sharing options...
7 wonders of the world Posted October 16, 2019 Share Posted October 16, 2019 How about redressing the Nitrons with some Billy decals...... Link to comment Share on other sites More sharing options...
anthonym Posted October 16, 2019 Author Share Posted October 16, 2019 Well actually, going to get the billies serviced by billy so they are ready to refit, not least because the nitrons are due a two year service. Link to comment Share on other sites More sharing options...
7 wonders of the world Posted October 16, 2019 Share Posted October 16, 2019 Are you going thro Control Technique in France or have I missed something and your going for a Swiss test...? Link to comment Share on other sites More sharing options...
SM25T Posted October 16, 2019 Share Posted October 16, 2019 Swiss all the way ! Link to comment Share on other sites More sharing options...
anthonym Posted October 16, 2019 Author Share Posted October 16, 2019 Swiss. Failed, have rectified all points except Nitrons approval which is in progress via conversation with the very helpful lady in charge at the test centre HQ. Attestations are always the secret ingredient. :-)anthony must type faster... Link to comment Share on other sites More sharing options...
7 wonders of the world Posted October 16, 2019 Share Posted October 16, 2019 Ouch - they really are picky aren't they.... Link to comment Share on other sites More sharing options...
anthonym Posted October 16, 2019 Author Share Posted October 16, 2019 Oh yes :-)want to see my fail list? Link to comment Share on other sites More sharing options...
anthonym Posted October 16, 2019 Author Share Posted October 16, 2019 Day lights not E marked. Replaced with E marked ones.Three rear fog lights, must remove one. Replaced with a second reversing light.Brake lights out. Fixed switch (embarrassed!)No plate light not lighting number plate. Now modified.Nitron shocks with Certificate, also required fitting certificate (attestation)from a Swiss garage.Failure to notify change of shocks from originals.. now notified. I hardly dare ask if I can fit JAL LED rear light clusters. Link to comment Share on other sites More sharing options...
7 wonders of the world Posted October 17, 2019 Share Posted October 17, 2019 simple answer is no as they are not 'e' marked AFAIK.There are others which are, SVC offer some dimensionally similar to the OE ones.or you can got for alternate shapes etc. Link to comment Share on other sites More sharing options...
TomB Posted October 17, 2019 Share Posted October 17, 2019 Are you allowed to fart while driving, or do you need a piece of paper for that too? Im late to this thread - can't you do anything a car in Switzerland to take it from standard without permission? Makes the UK seem positively liberal for once! Link to comment Share on other sites More sharing options...
revilla Posted October 17, 2019 Share Posted October 17, 2019 Not after 10:00pm, apparently. Oh no, that's peeing standing up (seriously). Link to comment Share on other sites More sharing options...
SM25T Posted October 17, 2019 Share Posted October 17, 2019 And no washing your car at home ... perish the thought !! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now