Jump to content
Click here if you are having website access problems ×

Why does my diff bang and clatter?


Andy Mac

Recommended Posts

And can I stop it ? Can it be adjusted to give clearance? It's LSD.

Over bumps It does sound like it's knocking the chassis.

Also it whine's a lot on overrun. I know this is a thing we have to accept, but can I sound proof to reduce at all?

Thanks.

Link to comment
Share on other sites

First thing, 'sounds like banging on the chassis', check all the fixing bolts as they do come loose over time, and I've known the bolts to break.

As for the whining, there are loads of threads re different types of LSDs making loads of noises, so you'll have to add what car you have and what diff is fitted, Ford or BMW to help answer your questions.

Link to comment
Share on other sites

The bottom two bolts where the BMW diff mounts to the carrier can work loose and drop out, (I upped the torque on mine to 110Nm, added blue Loctite and kept the Schnorr washers in place and have since had no problems). Also, if you have an old style carrier that mounts at the top to the diff using two of the cover bolts instead of a long bolt through the top of the cover, the cover bolts can hit the deDion tube when the car is corned hard (there was an upgraded cover available in 2014 or so to fix that problem).

Link to comment
Share on other sites

What about some sound proofing for the whining? Or am I being a bit anal?

On the basis the overall noise level whilst driving a Caterham is already high (mechanical, exhaust, wind etc.) anyway if you don't already wear them then earplugs or headphones are recommended if you're driving for any length of time.

Link to comment
Share on other sites

  • Area Representative

If you have check tightened all the attachments & there is no sign of fouling between back plate & de Dion then it has got to be the good old LSD. If it is a BMW ???

The banging & clattering is probably the backlash out of limits so that 'phenomena' is probably a combination of CWP & Titan.

There will be some whine on over run but if uncomfortably loud when taking the foot off the gas to decelerate from high speed - over 50/60 mph in 6th/5th - then there will be some mechanical noise.

A steady low pitched whine at set speeds, in certain gears & RPM can be attributable to either gear box or diff. But again if uncomfortably loud & from the rear - diff.

The Titan when lunching itself sort of screeches on cornering & when coasting at low speed to a stop, out of gear a low whine can be heard from the rear.

If you have a BMW LSD best to do the basic checks then escalate ! BMW Differential Titan limited slip unit - how to check & protect while in service. | Lotus Seven Club (lotus7.club)

To some degree TADTS is correct as there is a natural mechanical cacophony with a Sevens drive line BUT one should be able to disassociate the good from the bad.

Homework ! BMW/Titan LSD Viability | Lotus Seven Club (lotus7.club)

Link to comment
Share on other sites

My new build had terrible bang and chatter.  But its now all under control.  First I swapped the kit oil to Road and Race Transmissions specifically formulated blend.  Unfortunately it was as simple as that with my car.  By chance I was speaking with a 2021 spec kit builder, who asked where the gearbox spacer went, to which I replied what spacer.  It seem in 2021 Caterham introduced a spacer to lift the tail of the Mazda gearbox 3mm. This stopped 90% of my noises, which was suspected by Caterham themselves as diff noise, but obviously not.    This only applies to the 5speed, not the 6speed.

Sorry to say given the age of your car I would be checking the preload, and expecting a rebuild, unless you have a recent record of one. 

Link to comment
Share on other sites

It is, but your never find it, it has no image and is listed under *Seats and headrest fittings*.  Just search the part number 3E0G0002A.  It's £3.85, fits any 5 speed post 2013.  It fits between the gearbox and the gearbox mount, raising it by 3mm.  It can be fitted without removing anything other than the gearbox mount, I just supported the gearbox with a jack.  I believe the effect is most dramatic on Duratec cars, obviously I have only tried it in my 420R.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...